I might advocate acquiring it checked out by a tranny shop. The explanation I suggest This really is, whether it is the challenge I describe, the gears are actually rubbing the aspect with the transfer circumstance — and they're going to have on as a result of, effectively resulting in a good deal additional problems than in which you’re at now (ie. entire substitute of the TC).
The following detail I recognized was you stated the lights on the sprint will flash whenever you press 4Hi — this lets you know which the button for 4Hi is working, and the TCCM is accepting the signal from it. So, it boils all the way down to a problem someplace among the TCCM along with the encoder motor — I'd suspect the TCCM — probably wiring, or maybe a bad TCCM.
Seems to me like the transfer situation gears / forks — if you dig back by means of a number of the posts, I've explained the trouble you question of.
In any case I went to go use my four wheel drive one other working day soon after snow and I listen to the shafts interact but don't have any 4X4 in the slightest degree. Could I have destroyed the transfer circumstance or wiped out the splines around the CV joints. How do I repair it and what much do you think it is going to Price. Any enable can be considerably appreciated I ought to have took care of the challenge when I heard the grinding noise
I believed I’d give it a try to see what I could do (the plastic bag you see while in the 3rd picture contains a pair much more spare connectors just in case it ever takes place yet again… I’ll know proper exactly where They can be!).
Doesn’t seem fantastic. It looks like what I just went as a result of — and it turned out being the gears/forks while in the transfer circumstance. I initial found that I experienced problems popping out of 4WD, then I commenced noticing 4Hi “slipping†in and out.
I’ve nevertheless bought to obtain some schematics posted for another visitor poster over — hopefully I will make sure to do this these days. Regards;
Sad to say, it’s been Pretty much 9 a long time since I sold my Blazer and possess no further information for yourself other that what has Formerly been posted listed here.
Ryan suggests: April two, 2008 at nine:24 pm Many thanks with the response to my write-up before, And that i had pep boys do a vacuum take a look at to the system and they stated each individual thing was appeared to be Okay, so i bought that four wheel generate swith from napa and installed it,(it went into the entrance axle ideal where the cable from the actuator attaches), nonetheless no luck. so i could see some sort of sensor on top of the transfer circumstance with three vacuum traces hooked up to it, so i replaced i, and once again wheel alignment near me nonetheless very little, so i have a couple more queries…their is yet another sensor around the tail pice on the transfer scenario, I had been informed it is the velocity Regulate sensor, could that be the issue?
That’s an awesome story! Many thanks for sharing that with me… that's all I need! I’m not requesting anything, but hearing things similar to this would make me experience superior. Superior which i was capable to enable someone else out… and help save you some money in the process.
If you would like Check out some items and acquire back to me with some far more details/questions, I’d be satisfied to try to assistance you thru your challenge.
How to check In case the swap is negative? I’m not sure which switch you’re referring to, but no, I don't. I’d merely Google it more often than not to search out what I’m seeking. Almost everything that I ever needed to examination was uncovered as a result of Google.
Exact same matter as Pablo earlier mentioned. Your web site aided me a lot I cant thanks more than enough. Just a bit tip, I couldn’t locate any terminals within the electronics stores that might suit this connector, so I rigged some Laptop terminal wires plus they in shape just wonderful, no glue desired possibly. You saved me a “bunch of money†and I didn’t even have to switch to Geico.
The only issue you will have is as you have two wires disconnected, you have got to know which one goes to which gap (terminal). In case you inform me the colours, I am able to attempt to Find them for you personally (be unique with wire shades — ie. white with light inexperienced stripe, pink with dark blue stripe, and many others.).